INCRA TS-LS General Compatibility

www.incrementaltools.com

Rev 08/2022

28” x 21”

Left-side

Router

Table

28” x 32”

Right-side

Router

Table

32” x 21”

Left-side

Router

Table

32” x 32”

Right-side

Router

Table

Traditional 10” Contractor’s Saws

- 27” deep top, motor on rear of

saw, belt drive

Typical: Saw Stop Contractor’s saw, older

Sears Craftsman, Delta, older Jet JW-TS10,

Powermatic 64, Ridgid TS3650, etc.

9 N/A N/A

110V Hybrid-style Contractor’s or

Cabinet Saws - 27” deep cast iron top,

motor inside cabinet, small motor

cover/door on left side of cabinet

Typ ica l: Ridg id R4512, Cr af tsm an #21833,

Porter Cable PCB270TS, Jet JPS-10 Pro

Shop, Grizzly G0715P, General 50-200R,

Laguna Fusion, etc.

N/A N/A

Hybrid-style cabinet saw - 110V

motor underneath, wide motor

housing on right side of cabinet

Typical: Craftsman 922104, 922114, &

922124; Delta Hybrid 36-700 series, Steel

City, DeWalt DW746, etc.

N/A N/A

Non-standard, hybrid-style cabi-

net saw - 110V motor underneath

Jet Super Saw (JW-SS10-xxx). Motor un-

derneath, access door ush with cabinet,

110V m otor

Portable jobsite table saws or

small stationary saws, 19”-25”

table depth

Typical: Bosch 4100, Ridgid 4510, DeWalt

DW745, etc.

Standard right-tilt 10” Cabinet

Saws: 27”-28” deep top, 220 Volt

motor underneath, motor door on

right side of cabinet

Typical: Jet JTAS-10, pre-2009 right-tilt

Delta Unisaw, General 350, Grizzly 1023R,

Steel City, etc.

Standard left-tilt 10” Cabinet Saws:

27”-28” deep top, 220 Volt motor

underneath, motor door on left

side of cabinet

Typical: Powermatic 66, Saw Stop PCS,

pre-2009 left-tilt Delta Unisaw, Jet JTAS-

10L, General 650, Grizzly G0690 & 1023L,

Steel City, etc.

Oversized Cabinet Saws: 30”-31”

deep top, 220 Volt motor under-

neath, motor door on right side

of cabinet

Typical: Saw Stop 10” Industrial Cabinet

Saw, older Grizzly & Jet 12” right-tilt saws,

etc.

N/A 2

Oversized left-tilt 10” Cabinet

Saws: 30”-31” deep top, 220 Volt

motor underneath, motor door on

left side of cabinet

Typical: Powermatic PM-2000, post-2009

Delta Unisaw, etc.

N/A N/A

Non-standard, oversized European

cabinet saw

Laguna TS 10”, Laguna TSS 12”

N/A N/A N/A

Notes:

1. Drilling of rail mounting holes either likely or required

2. Requires 92” rails / 52”-capacity TS-LS to move router clear of saw’s motor housing

3. Rails must be positioned to the far right during installation

4. Order “XL” version of TS-LS; saw’s extra depth requires longer-than-standard fence

and base support panel

5. Requires either custom-depth router table or shop-made extension for router table

hardware

6. Not compatible with sliding table

7. Use of sliding table requires drilling rail mounting holes

8. INCRA Router Tables must be cut to a shorter depth for use on saws smaller than

26-3/4” front to rear

9. Rail support legs required under right-hand end

10. Fence and base support panel will be longer than necessary

11. Saw MUST have at, vertical surfaces front & rear after original fence rails are removed

12. Measure for clearance; after removing the left-side cast iron wing, motor housing/

cover on side of saw must not protrude more than 5-1/4” beyond the central top to

clear the router opening or protrude more than 3-3/8” to use the INCRA CleanSweep

Cabinet

Typical installation - saw’s power switch may need to be adapted to the front INCRA rail; metric mounting bolts may be required for

some saws; the original splitter/guards on older saws may interfere with rear INCRA rail.

1, 6 1, 6, 10 N/A

1, 9, 11

8, 9 8, 9 N/A

2 N/A

N/A N/A

TS-LS fence systems are straightforward installations on a huge variety of table saws - so many that it’s not practical to

list them all, but the vast majority of the saws on the market will fall into the categories listed in the chart.



Table saw size:

The saw’s left-to-right width won’t matter for systems not equipped with router tables. To match the front-to-rear depth of the saw, the

TS-LS system is available in two versions: a “standard” model for traditional 10” oor-standing saws 28”-deep or less, and an “XL” version

that ts most of the newer cabinet saws with deeper tops measuring 33.5” or less.

Basic saw requirements:

The saw’s top must have at, vertical surfaces on both the front and rear for the (4) adjustable Incra rail mounting brackets to bolt against –

two at the front and two on the rear. The brackets are attached with a minimum 5/16”-18 bolt (or 8mm), and the holes need to be centered

between 3/4” and 1-3/8” down from the top, with enough clearance underneath the saw’s top for the washers, nuts and wrench (if the

holes aren’t threaded).

The TS-LS owner’s manual is the best resource for seeing how the 4 rail mounting brackets attach and comparing that to your saw:

http://www.incra.com/manuals/ts_ls_manual.pdf

32” TS-LS

52” TS-LS

32” TS-LS XL

52” TS-LS XL

Saw Type

Common Examples

N/A

N/A N/A

N/A

N/A = not compatible