900 MHZ TRANSMITTERS & RECEIVER

75.5786.04 900 MHZ 20161027 Page 1 of 4

10TD900HH410TD900HH310TD900HH2

10TD900HH410TD900HH310TD900HH1

75.5786.04 900 MHZ 20161027 Page 1 of 4

Digital transmitters and receiver

with frequency hopping, sequencing

and extended hold functionality

(US version)

ENGLISH

1. receiver (10RD900)

2. antenna wire

3. blue activation LED

4. red learn LED

5. tri-color signal strength LED

6. DIP switches

7. no-delay learn button

8. delay learn button

9. delay learn POT

10. transmitter (10TD900PB)

11. push plate connectors

12. battery cradle

HAND HELD TRANSMITTERS

DESCRIPTION

IMPORTANT:

This wireless receiver is not intended to be used DIRECTLY with maglocks or electric

strikes due to possible damage caused by inductive load kickback.

Instead, this wireless receiver should be used to trigger a logic module (Br3) or

isolation relay which then triggers the maglock or electric strike.

Page 2 of 4 75.5786.04 900 MHZ 20161027

1 2 3

PUL | TOG

0.5s | 10s

REG | EH

1 2 3

Page 2 of 4 75.5786.04 900 MHZ 20161027

• The device should not be used for purposes other than its intended use. All other uses cannot be guaranteed by

the manufacturer of the sensor.

• The installer of the door system is responsible for carrying out a risk assessment and installing the sensor and the

door system in compliance with applicable national and international regulations and standards on door safety.

• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate adjustments

of the sensor.

PRECAUTIONS

q Shut off all power going to header before attempting any wiring procedures.

q Maintain a clean & safe environment when working in public areas.

q Constantly be aware of pedestrian trafﬁc around the door area.

q Always stop pedestrian trafﬁc through the doorway when performing tests that may result in unexpected reactions

by the door.

q ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge. Before handling

any board ensure you dissipate your body’s ESD charge.

q Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires

and cause damage to equipment.

q Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.

q DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be

performed by BEA, Inc. Unauthorized disassembly or repair:

1. May jeopardize personal safety and may expose one to the risk of electrical shock.

2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.

Hand Held Conﬁguration

INSTALLATION

Wiring

TERMINAL: 1 2 3 4 5

LABEL: 12-24 V 12-24 V COM NO NC

WIRE COLOR: red black white green yellow

SIGNAL: + voltage - voltage common normally open normally closed

DESCRIPTION: power relay contacts

SETUP

DIP Switches

DIP

STATUS

FUNCTION DESCRIPTION

OFF

PUL Pulse Relay pressing transmitter activates and holds relay according to DIP 2 and 3

TOG

Toggle

Relay

pressing transmitter once activates and holds relay indeﬁnitely

pressing transmitter again deactivates relay immediately (no hold)

(PUL only)

OFF

0.5s

0.5 second

hold time

relay remains active for 0.5 seconds after transmitter is...

pressed [STD] released [EH]

10s

10 second

hold time

relay remains active for 10 seconds after transmitter is...

pressed [STD] released [EH]

OFF

REG

standard

hold

relay acts according to DIP 1 and 2

(does not matter if transmitter is pressed/released or pressed/held)

extended

hold

relay remains active as long as transmitter is pressed and held

once released, relay acts according to DIP 1 and 2

Set DIP switches as desired. Press transmitter twice (blue LED

on receiver will illuminate).

Press and release desired learn button

(red LED on receiver will illuminate)

NOTES:

If Learn w/ Delay button is used, adjust potentiometer (1 s to 30 s).

75.5786.04 900 MHZ 20161027 Page 3 of 4

2 1

1 2 3

PUL | TOG

0.5s | 10s

REG | EH

3 V

AAA Battery

OUTER

RECEIVER

INNER

RECEIVER

75.5786.04 900 MHZ 20161027 Page 3 of 4

All Transmitters

Removing Transmitters

Single Transmitter

Press BOTH learn buttons until

red LED ﬂashes once (~2 s).

Press BOTH learn buttons until

blue LED illuminates (~10 s).

Press transmiter TWICE within

10 seconds.

SETUP (cont.)

Push Plate Conﬁguration

Connect transmitter

to push plate

(NO & COM) and insert into box.

Follow steps 1-3 in Hand Held

Conﬁguration

Install push plate.

NOTES: 1: 10TD900PB required for push plates

Vestibule Conﬁguration

RECEIVER TRANSMITTER LEARN

Outer

outer (1) No Delay

inner (2) Delay

vestibule (4) No Delay

Inner

outer (1) Delay

inner (2) No Delay

vestibule (3) No Delay

Battery Replacement

Push Plate (TD900PB)Handheld (TD900HHx)

Remove back screws and

disassemble.

Replace 2 AAA batteries

observing polarity.

Replace 3 volt (CR2032) battery

observing polarity and reassemble.

Low Battery Indicator - After transmitter button is pressed, low battery is indicated by three (3) transmiter LED blinks.

Signal Strength Indicator - Pressing and holding transmitter button for 3 seconds activates signal strength tri-color LED

on receiver. Green = strong signal, Yellow = medium signal, Red = weak signal.

For vestibule applications, program each receiver to the appropriate

transmitters according to the chart below and the picture to the right.

NOTE: All transmitters must ONLY be powered with provided batteries or equivalent.

Page 4 of 4 75.5786.04 900 MHZ 20161027

©BEA | Original Instructions | 75.5786.04 900 MHZ 20161027

FCC ID: 2ABWS-10RD900 IC: 4680A-10RD900 MODEL: 10RD900

FCC ID: 2ABWS-10TD900PB IC: 4680A-10TD900PB MODEL: 10TD900PB

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH1

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH2

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH3

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH4

Page 4 of 4 75.5786.04 900 MHZ 20161027

Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the minimum

inspection guidelines provided by AAADM. Provide each equipment owner with an owner’s manual that includes a daily safety

checklist and contains, at a minimum, the information recommended by AAADM. Offer an information session with the equipment

owner explaining how to perform daily inspections and point out the location of power/operation switches to disable the equipment if

a compliance issue is noted. The equipment should be inspected annually in accordance with the minimum inspection guidelines. A

safety check that includes, at a minimum, the items listed on the safety information label must be performed during each service call.

If you are not an AAADM certiﬁ ed inspector, BEA strongly recommends you have an AAADM certiﬁ ed inspector perform an AAADM

inspection and place a valid inspection sticker below the safety information label prior to putting the equipment into operation.

ANSI / AAADM Compliance

PLEASE KEEP FOR FURTHER USE – DESIGNED FOR COLOR PRINTING

Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: T[email protected] | Tech Docs: www.beasensors.com

TECHNICAL SPECIFICATIONS

Frequency: 908-918 MHz (frequency hopping)

Emitted radio power: -25 dBm (TX)

Power consumption: 30mA (TX)

40mA (RX)

Supply voltage: 12-24 VAC/DC

Contact rating: 1.0 A @ 30 VDC

0.5 A @ 125 VAC

0.3 A @ 60 VDC

Temperature range: 14°F to 131°F (-10°C to 55°C)

Programmable units per receiver: 75

LEDs: red (receiver learn)

blue (relay activation)

tri-color (signal strength)

Dimensions: 2.5” (W) x 2.0” (D) x 0.75” (H) [RD900]

2.75” (W) x 1.38” (D) x 0.56” (H) [TD900HHx]

1.75” (W) x 1.0” (D) x 0.3” (H) [TD900PB]

Certiﬁcation: FCC, IC

Speciﬁcations are subject to changes without prior notice.

All values measured in speciﬁc conditions.

red LED on receiver

ﬂickering; unable to

program

stuck push plate

disconnect push plates to determine which is

stuck (LED should go out)

faulty transmitter

if LED does not go out, remove transmitter

batteries to determine which is faulty, replace

transmitter

weak signal

receiver antenna positioned

poorly

position antenna outside of door header

TROUBLESHOOTING

FCC / IC

“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.”

Changes or modiﬁcations not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

FCC ID: 2ABWS-10RD900 IC: 4680A-10RD900 MODEL: 10RD900

FCC ID: 2ABWS-10TD900PB IC: 4680A-10TD900PB MODEL: 10TD900PB

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH1

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH2

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH3

FCC ID: 2ABWS-10TD900HH4 IC: 4680A-10TD900HH4 MODEL: 10TD900HH4